For a podcast recorded in an untreated home room, buy a cardioid dynamic microphone, and if it is a passive XLR mic like the Shure SM7B, give it at least 60 dB of clean preamp gain, which is the minimum Shure recommends for the SM7B. Call that the 60 dB rule. For most solo hosts, a hybrid USB and XLR dynamic mic such as the Shure MV7+ or RODE PodMic USB avoids the gain problem entirely, because the preamp is built in.
This guide is for marketers, founders and creators recording podcasts, webinars and voice-over from a home office. We did not test these microphones hands-on. We compared published manufacturer specifications, Shure's own technical guidance on gain and room noise, and Amazon prices as of November 2026.
Podcast microphone comparison table.
| Pick | Best for | Type | Outputs | Digital resolution | Frequency response | Price |
|---|---|---|---|---|---|---|
| Shure SM7B / SM7dB | Studio-grade voice, XLR setup | Dynamic, cardioid | XLR only | Not applicable (analog) | 50 Hz to 20 kHz | About $369 / $459 |
| Shure MV7+ | Best overall for solo hosts | Dynamic, cardioid | USB-C and XLR | 24-bit, 48 kHz | 50 Hz to 16 kHz | About $255 |
| RODE PodMic USB | Broadcast sound with built-in DSP | Dynamic, cardioid, end address | USB-C and XLR | 24-bit, 48 kHz | 20 Hz to 20 kHz | About $167 |
| Elgato Wave:3 MK.2 | Streamers in a quiet room | Condenser, cardioid | USB-C | 24-bit, 48 kHz | 70 Hz to 20 kHz | About $145 |
| Audio-Technica ATR2100x-USB | Budget USB and XLR | Dynamic, cardioid | USB-C and XLR | Up to 24-bit, 192 kHz | 50 Hz to 15 kHz | About $77 |
| Samson Q2U | Cheapest hybrid pack | Dynamic, cardioid | USB-C and XLR | Up to 16-bit, 44.1/48 kHz | 50 Hz to 15 kHz | About $80 |
| DJI Mic 2 | Video podcasts and on-camera | Wireless lavalier, omnidirectional | 3.5 mm and receiver outputs | 32-bit float internal recording | Not listed | About $199 (2 TX) |
| RODE Wireless GO (Gen 3) | Two-person video interviews | Wireless, 2 TX + 1 RX | Digital and analog outputs | 32-bit float on-board recording | Not listed | About $184 (2 TX) |
| Logitech Blue Yeti | Multi-pattern, one-mic table | Condenser, 4 patterns | USB | 16-bit, 48 kHz | 20 Hz to 20 kHz | About $100 |
Dynamic vs condenser for untreated rooms.
The first choice is the capsule type, and the room decides it. Shure's streaming buyer's guide matches dynamic mics to "bedrooms, gaming setups and untreated rooms" and condensers to "quiet or acoustically treated rooms," noting that a condenser's greater sensitivity can capture more of the surrounding room. Shure's podcast microphone guide says home spaces usually have background noise from air vents, appliances and computer fans, and that condensers can pick up vent hiss and mouth noise that dynamics mask.
The trade-off is level. In its SM7B gain article, Shure says the dynamic SM7 has an output level 28 dB lower than its KSM44 condenser in cardioid. Lower output is part of why a dynamic rejects the room, and it is why dynamics need more gain.
| Your room | Pick | Why |
|---|---|---|
| Bedroom, home office, hard floors, HVAC noise | Dynamic, cardioid | Lower sensitivity picks up less room and background sound (Shure) |
| Treated studio or very quiet room | Condenser is fine | Better high-frequency detail; room noise is under control |
| Several people around one table | Multi-pattern condenser (omni) or one dynamic per person | One mic per voice gives cleaner editing; omni is the fallback |
| Video podcast where the mic must stay out of frame | Wireless lavalier | Fixed distance to the mouth, no desk mic in shot |
Distance matters as much as type. Shure's podcast guide recommends placing the mic 2 to 12 inches from your mouth so your voice is louder relative to room noise and reflections. A dynamic mic used 2 feet away will sound worse than a condenser used 6 inches away.
USB vs XLR podcast microphones.
A USB microphone has its own preamp and converter inside, so it plugs straight into a laptop. An XLR microphone sends an analog signal that needs an audio interface or mixer. Hybrid microphones with both outputs are the default recommendation for new podcasters, because you can start on USB and move to an interface later without buying a new mic.
| USB only | XLR only | Hybrid USB and XLR | |
|---|---|---|---|
| Extra hardware | None | Interface or mixer with enough gain | None to start; interface optional |
| Multiple hosts on one computer | Awkward (each USB mic is its own device) | Easy through a multi-input interface | Easy over XLR |
| Built-in processing | Often (for example Elgato Clipguard 2.0, RODE APHEX DSP) | No | On the USB side only |
| Examples here | Elgato Wave:3 MK.2, Blue Yeti | Shure SM7B, SM7dB | Shure MV7+, RODE PodMic USB, ATR2100x-USB, Samson Q2U |
One detail generic guides skip: on hybrid mics, the software settings usually apply only to the USB output. Shure's MV7+ user guide describes the XLR output as passive and notes that software settings do not affect XLR audio. If you want the onboard processing, record over USB.
The 60 dB rule for the Shure SM7B.
Shure's support article lays out the math. At an acoustic input of 84 dB SPL, which Shure gives as typical speech level at 3 inches, the SM7 outputs -69 dBV. The preamp has to bring that up toward 0 dBV line level, and +60 dB of gain gets it to -9 dBV, which Shure calls close enough. Shure's SM7B spec sheet lists the output level as -59.0 dB (1.12 mV) at 1 kHz, where 0 dB is 1 volt per pascal.
Shure adds that many modern preamps, mixers and interfaces assume a condenser mic and offer only 40 to 50 dB of gain, which is not enough. Its fixes, in Shure's words, are an interface with at least 60 dB of gain (it names its own MVX2U at 60 dB total), or a phantom-powered inline preamp such as the sE DM1 or DM2, Triton FetHead or Cloudlifter, which add 25 to 28 dB.
| Mic | XLR sensitivity | Built-in gain | What to plug it into |
|---|---|---|---|
| Shure SM7B | -59.0 dBV/Pa (1.12 mV) | None | An interface with 60 dB or more, or an inline preamp |
| Shure SM7dB | Not listed on product page | +18 dB or +28 dB preamp (needs +48V phantom) | Any interface with phantom power |
| Shure MV7+ | -55 dBV/Pa (1.78 mV) | 0 to +36 dB on the USB side | USB-C directly, or an interface over XLR |
| RODE PodMic USB | -57 dB re 1 V/Pa (1.4 mV) | Revolution Preamp on the USB side | USB-C directly, or an interface over XLR |
The best podcast microphones by use case.
Shure SM7B and SM7dB: best XLR podcast microphone.
Best for: hosts building a permanent studio with an interface, and teams that want the mic most broadcast listeners already recognize. Shure SM7B (about $369 on Amazon as of November 2026) or Shure SM7dB (about $459).
The SM7B spec sheet lists a cardioid dynamic capsule, 50 Hz to 20 kHz frequency response, 150 ohm impedance, an XLR connector, bass roll-off and presence boost switches, an internal air-suspension shock mount, and a net weight with cable of 851.6 g. The SM7dB adds a selectable +18 dB or +28 dB built-in preamp with a bypass switch, and requires +48V phantom power from your interface.
Downside: the SM7B is XLR only and needs 60 dB of clean gain, so the true cost includes an interface or an inline preamp. The SM7dB costs about $90 more but removes the inline preamp from the shopping list.
Shure MV7+: best podcast microphone overall.
Best for: solo hosts, founders recording a weekly show, and anyone who wants SM7-style dynamic sound without an interface. Shure MV7+ (about $255 on Amazon as of November 2026).
Shure's MV7+ user guide lists a cardioid dynamic (moving coil) transducer, 50 Hz to 16,000 Hz frequency response, 0 to +36 dB adjustable gain, -55 dBV/Pa XLR sensitivity, 24-bit and 48 kHz over USB, and a net weight of 573.5 g. Shure's product page lists dual USB-C and XLR outputs, an Auto Level Mode that adjusts gain based on distance and volume, a digital pop filter, and a real-time denoiser.
Downside: the processing applies on USB only, and the frequency response tops out at 16 kHz versus 20 kHz on the SM7B. For spoken word that rarely matters, but it is the trade-off for the built-in convenience.
RODE PodMic USB: best value broadcast dynamic.
Best for: podcasters who want a heavy, broadcast-style mic with built-in processing for well under $200. RODE PodMic USB (about $167 on Amazon as of November 2026).
RODE's datasheet lists a dynamic, cardioid, end-address capsule, 20 Hz to 20 kHz frequency range, 148 dB SPL maximum, -57 dB re 1 V/Pa sensitivity, XLR and USB-C outputs, 24-bit and 48 kHz digital resolution, a Revolution Preamp, APHEX processing (compressor, noise gate, high-pass filter, Aural Exciter and Big Bottom), a 3.5 mm headphone jack and a weight of 900 g.
Downside: 900 g is heavy, so it needs a sturdy boom arm. A light desk stand will tip.
Elgato Wave:3 MK.2: best USB condenser for streamers.
Best for: live streamers and hosts in a quiet or treated room who want onboard DSP and protection from sudden loud sounds. Elgato Wave:3 MK.2 (about $145 on Amazon as of November 2026).
Elgato's product page lists a 16 mm condenser capsule with an integrated JFET, cardioid pattern, 24-bit and 48 kHz resolution, 70 Hz to 20 kHz frequency response, USB-C (USB 2.0 HS) with a 3.5 mm headphone jack, Clipguard 2.0 anti-distortion on its Wave FX processor, and an auto gain setup you start by holding the dial for 5 seconds. Elgato listed it at $149.99 on sale (from $169.99) on its own store as of November 2026.
Downside: it is a condenser. In an untreated room with an air vent or a noisy PC, Shure's guidance (and physics) says it will pick up more of the room than the dynamic picks.
Audio-Technica ATR2100x-USB: best budget USB and XLR microphone.
Best for: a first podcast mic, or a second guest mic, that can grow into an interface setup. Audio-Technica ATR2100x-USB (about $77 on Amazon as of November 2026).
Audio-Technica's user manual lists a dynamic, cardioid element, 50 to 15,000 Hz frequency response, up to 24-bit and 192 kHz on USB, both USB and XLR outputs, and a weight of 268 g. It also says the default sample rate is 44.1 kHz, and that if you record voice-over that will be synced with video, you need to change it to 48 kHz, and that the rate must match your recording app or you will hear pops and clicks.
Downside: it is a handheld-style mic. It works on a stand, but it lacks the shock mounting and presence of the larger broadcast picks.
Samson Q2U: best cheapest hybrid podcast pack.
Best for: outfitting two or three guest seats cheaply with matching dynamic mics. Samson Q2U (about $80 on Amazon as of November 2026).
Samson's product page lists a dynamic capsule with a cardioid pattern, 50 Hz to 15 kHz frequency response, up to 16-bit and 44.1 or 48 kHz over USB-C, an XLR output, a 3.5 mm zero-latency headphone output with level control, and a weight of 0.32 kg.
Downside: 16-bit is the ceiling on USB. That is fine for spoken word, but it leaves less headroom than the 24-bit picks if you set levels too low.
DJI Mic 2: best wireless mic for video podcasts.
Best for: video podcasts, founder videos and walk-and-talk content where a desk mic would be in frame. DJI Mic 2, two transmitters (about $199 on Amazon as of November 2026).
DJI's spec page lists a 28 g transmitter, an omnidirectional pattern, 250 m range under FCC (160 m under CE) in open, unobstructed conditions, and 6 hours of operating time per transmitter and receiver. Its product page lists 14-hour internal recording and 32-bit float internal recording, which acts as a backup if the wireless link drops.
Downside: omnidirectional lavaliers hear the whole room. They sound best when clipped close to the mouth, and they will not reject room noise the way a cardioid dynamic on a boom arm does.
RODE Wireless GO (Gen 3): best wireless alternative.
Best for: two-person interviews on camera, recorded straight into a phone, camera or computer. RODE Wireless GO (Gen 3), two transmitters (about $184 on Amazon as of November 2026).
RODE's product page lists range up to 260 m line of sight, 32-bit float on-board recording on each transmitter so clipped or quiet audio can be recovered, GainAssist automatic level control, digital and analog outputs, and 3.5 mm locking connectors for external lavaliers.
Downside: RODE's product page does not publish battery life or recording hours, so you cannot compare runtime with the DJI Mic 2 from manufacturer pages alone.
Logitech Blue Yeti: best multi-pattern USB microphone.
Best for: occasional two-person recordings around one mic, or a single USB mic that can switch patterns. Logitech Blue Yeti (about $100 on Amazon as of November 2026).
Logitech's product page lists a 3-capsule condenser array with cardioid, bidirectional, omnidirectional and stereo patterns, 16-bit and 48 kHz resolution, and 20 Hz to 20 kHz frequency response. Logitech listed it at $109.99 on its own store as of November 2026.
Downside: it is a condenser, so it hears keyboards, desks and room echo. In an untreated room, a dynamic pick at the same price will usually sound cleaner.
How to choose a podcast microphone.
Related gear guides.
If your podcast is also a video show, pair the mic with the right camera: see our guide to the best webcam for streaming, including the iPhone-as-webcam option. For a second screen to run your recording software and notes, see the best portable monitors. If you are cutting episodes into ads, our YouTube ad specs and TikTok ad specs pages list the lengths and ratios each platform accepts.
Podcast microphone questions people ask.
Is a dynamic or condenser microphone better for podcasting?
In an untreated home room, dynamic. Shure's own guidance matches dynamic mics to bedrooms and untreated rooms, where they pick up less background sound, and condensers to quiet or acoustically treated rooms. Condensers capture more high-frequency detail, but also more room noise.
How much gain does the Shure SM7B need?
Shure recommends a preamp with a minimum of 60 dB of gain. At typical speech level the SM7B outputs about -69 dBV, and many interfaces offer only 40 to 50 dB. Inline preamps such as the Cloudlifter add 25 to 28 dB, and the SM7dB has a built-in +18 or +28 dB preamp.
Do I need a Cloudlifter for the SM7B?
Only if your interface cannot supply about 60 dB of clean gain. Check the interface's published maximum gain. If it is in the 40 to 50 dB range, an inline preamp (25 to 28 dB per Shure) or the SM7dB solves it.
Should I buy a USB or XLR podcast microphone?
For one host on one laptop, a USB or hybrid mic is simpler. For two or more people in the same room, XLR into a multi-input interface keeps each voice on its own track. Hybrid mics like the Shure MV7+ and RODE PodMic USB let you start on USB and move to XLR later.
What sample rate should I record a podcast at?
48 kHz at 24-bit when the mic supports it. Most of our picks run at 24-bit and 48 kHz over USB, and Audio-Technica's ATR2100x-USB manual says to switch from its 44.1 kHz default to 48 kHz for audio that will sync with video.
What microphone should I use for a video podcast?
Either a dynamic mic on a low-profile boom arm kept just out of frame, or a wireless lavalier such as the DJI Mic 2 or RODE Wireless GO (Gen 3). Both wireless systems record 32-bit float audio on the transmitter as a backup.